Enhance your career with NSE6_FWF-6.4 PDF Dumps - True Fortinet Exam Questions
New (2024) Download free NSE6_FWF-6.4 PDF for Fortinet Practice Tests
The NSE6_FWF-6.4 (Fortinet NSE 6 - Secure Wireless LAN 6.4) Certification Exam is an essential certification for cybersecurity professionals who work with Fortinet's secure wireless LAN solutions. NSE6_FWF-6.4 exam is designed to test the candidate's understanding of Fortinet's wireless LAN technologies and their ability to configure, manage, and troubleshoot these solutions. Successful candidates will be able to demonstrate their expertise in the administration and management of Fortinet's secure wireless LAN solutions.
NEW QUESTION # 12
You are investigating a wireless performance issue and you are trying to audit the neighboring APs in the PF environment. You review the Rogue APs widget on the GUI but it is empty, despite the known presence of other APs.
Which configuration change will allow neighboring APs to be successfully detected?
- A. Enable Locate WiFi clients when not connected in the relevant AP profiles.
- B. Enable Radio resource provisioning on the relevant AP profiles.
- C. Enable Monitor channel utilization on the relevant AP profiles.
- D. Ensure that all allowed channels are enabled for the AP radios.
Answer: B
Explanation:
The ARRP (Automatic Radio Resource Provisioning) profile improves upon DARRP (Distributed Automatic Radio Resource Provisioning) by allowing more factors to be considered to optimize channel selection among FortiAPs. DARRP uses the neighbor APs channels and signal strength collected from the background scan for channel selection.
NEW QUESTION # 13
As standard best practice, which configuration should be performed before configuring FortiAPs using a FortiGate wireless controller?
- A. Preauthorize APs
- B. Set the wireless controller country setting
- C. Create a custom AP profile
- D. Create wireless LAN specific policies
Answer: B
NEW QUESTION # 14
Refer to the exhibit.
What does the asterisk (*) symbol beside the channel mean?
- A. Indicates channels that can be used only when Radio Resource Provisioning is enabled
- B. Indicates channels that are subject to dynamic frequency selection (DFS) regulations
- C. Indicates channels that cannot be used because of regulatory channel restrictions
- D. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)
Answer: B
Explanation:
Explanation
This frequencies are also used by other licensed applications, wireless LANs have to use a specific method to gain access to certain higher frequencies and this method is known as DFS.
NEW QUESTION # 15
Which of the following is a requirement to generate analytic reports using on-site FortiPresence deployment?
- A. DTLS encryption on wireless traffic must be turned off
- B. Wireless network security must be set to open
- C. Two wireless APs must be sending data
- D. SQL services must be running
Answer: D
NEW QUESTION # 16
Which statement describes FortiPresence location map functionality?
- A. Provides real-time insight into user online activity
- B. Provides real-time insight into user purchase activity
- C. Provides real-time insight into user usage stats
- D. Provides real-time insight into user movements
Answer: D
Explanation:
Explanation
(Page 88 Study Guide) "FortiPresence provides data and analytics based on demographic segmentation and visitor movement between areas" According to the web search results, FortiPresence location map functionality provides real-time insight into user movements. It uses the location data from the Fortinet access points to detect each visitor's smartphone Wi-Fi signal and track their location and behavior within the site. It also provides data visualization in a customizable format, such as heat maps and animated flows, to show the visitor traffic and movement patterns.
This geographical data analysis can help improve visitor experiences and business outcomes.
References: Location Analytics | FortiPresence 22.4.0 - Fortinet Documentation, FortiPresence Data Sheet
NEW QUESTION # 17
When deploying a wireless network that is authenticated using EAP PEAP, which two configurations are required? (Choose two.)
- A. A WPA2 or WPA3 Enterprise wireless network
- B. An X.509 certificate to authenticate the client
- C. An X.509 to authenticate the authentication server
- D. 509 certificates and work for connections that use Secure Socket Layer/Transport Level Security (SSL/TLS). Both client and server certificates have additional requirements.
- E. A WPA2 or WPA3 personal wireless network
Answer: B,C
NEW QUESTION # 18
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength weaker than -68 dB are shown with blackbackground.
- B. Areas with the signal strength equal to -68 dB are zoomed in to providebetter visibility.
- C. Areas with the signal strength weaker than -68 dB are highlighted in orangeand red to indicate that no signal was propagated by the APS.
- D. Areas with the signal strength equal or stronger than -68 dB are highlighted in green circles.
Answer: D
Explanation:
Explanation
The FortiPlanner site survey reading is a tool that shows the predicted signal strength of the wireless network based on the floor plan, the placement of the APs, and the propagation model. The signal strength is measured in decibels (dB), which is a logarithmic scale that indicates how much power the signal has. The higher the dB value, the stronger the signal.
The site survey reading allows the user to set a threshold value for the signal strength, which is -68 dB by default. This means that any area with a signal strength equal or stronger than -68 dB is considered to have adequate coverage for most wireless applications. These areas are highlighted in green circles on the floor plan. Any area with a signal strength weaker than -68 dB is considered to have poor coverage or no coverage at all. These areas are shown with different colors, such as yellow, orange, red, or black, depending on how weak the signal is.
Therefore, the correct answer is D. Areas with the signal strength equal or stronger than -68 dB are highlighted in green circles.
References:
FortiPlanner 2.0 User Guide, page 28
FortiPlanner Data Sheet, page 2
FortiPlanner 2.2 User Guide, page 19
NEW QUESTION # 19
What is the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration?
- A. Multicast
- B. DHCP
- C. Static
- D. Broadcast
Answer: C
Explanation:
Explanation
According to the web search results, the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration is static. This means that the FortiAP sends discovery requests to a preconfigured IP address that the controller owns. This is useful if the FortiAP and the controller are not in the same subnet and other discovery methods will not work. The other discovery methods are used in sequence if the static method fails or is not configured. References: Advanced WiFi controller discovery | FortiAP / FortiWiFi 7.4.0
NEW QUESTION # 20
When using FortiPresence as a captive portal, which two types of public authentication services can be used to access guest Wi-Fi? (Choose two.)
- A. Short message service authentication
- B. Software security token authentication
- C. Hardware security token authentication
- D. Social networks authentication
Answer: A,D
NEW QUESTION # 21
When configuring Auto TX Power control on an AP radio, which two statements best describe how the radio responds? (Choose two.)
- A. When the AP detects PF Interference from an unknown source such as a cordless phone with a signal stronger that -70 dBm, it will increase its transmission power until it reaches the maximum configured TX power limit.
- B. When the AP detects any other wireless signal stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
- C. When the AP detects any interference from a trusted neighboring AP stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
- D. When the AP detects any wireless client signal weaker than -70 dBm, it will reduce its transmission power until it reaches the maximum configured TX power limit.
Answer: B,C
Explanation:
Explanation
According to the web search results, Auto TX Power control is a feature that allows the AP to automatically adjust its transmission power based on the RF environment. The goal is to minimize interference and optimize coverage cells for roaming. When the AP detects any other wireless signal stronger than -70 dBm, it means that there is a potential source of interference nearby, so it will reduce its transmission power until it reaches the minimum configured TX power limit. This will reduce the interference and improve coexistence with other devices. When the AP detects any interference from a trusted neighboring AP stronger than -70 dBm, it means that there is a high density of APs in the area, so it will also reduce its transmission power until it reaches the minimum configured TX power limit. This will balance the load and avoid overlapping coverage areas.
References: AP Transmit Power and Enable Power Reduction with Auto TX, Transmit Power and Antenna Configuration, Meraki Auto RF: Wi-Fi Channel and Power Management
NEW QUESTION # 22
Refer to the exhibits.
Exhibit A
Exhibit B
The exhibits show the diagnose debug log of a station connection taken on the controller CLI.
Which security mode is used by the wireless connection?
- A. WPA3 Enterprise
- B. Open, with radius MAC filtering
- C. WPA2 Personal and radius MAC filtering
- D. WPA2 Enterprise
Answer: D
Explanation:
Best security option is WPA2-AES.
NEW QUESTION # 23
As a network administrator, you are responsible for managing an enterprise secure wireless LAN. The controller is based in the United States, and you have been asked to deploy a number of managed APs in a remote office in Germany.
What is the correct way to ensure that the RF channels and transmission power limits are appropriately configured for the remote APs?
- A. Create a new FortiAP profile and change the county code settings on the profile
- B. Clone a suitable FortiAP profile and change the county code settings on the profile
- C. Configure the controller for the correct country code for Germany
- D. Configure the APs individually by overriding the settings in Managed FortiAPs
Answer: B
NEW QUESTION # 24
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit C
A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and IoT devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?
- A. Install another AP in the reception area to improve available bandwidth
- B. Increase the transmission power of the AP radios
- C. Enable frequency handoff on the AP to band steer clients
- D. Reduce the number of wireless networks being broadcast by the AP
Answer: C
NEW QUESTION # 25
Which two phases are part of the process to plan a wireless design project? (Choose two.)
- A. Installation phase
- B. Hardware selection phase
- C. Site survey phase
- D. Project information phase
Answer: A,C
Explanation:
Reference:
https://www.automation.com/en-us/articles/2015-2/wireless-device-network-planning-and-design
NEW QUESTION # 26
Which two statements about background rogue scanning are correct? (Choose two.)
- A. A dedicated radio configured for background scanning can detect rogue devices on all other channels in its configured frequency band
- B. Background rogue scanning requires DARRP to be enabled on the AP instance
- C. A dedicated radio configured for background scanning can support the connection of wireless clients
- D. When detecting rogue APs, a dedicated radio configured for background scanning can suppress the rogue AP
Answer: C,D
Explanation:
To enable rogue AP scanning
NEW QUESTION # 27
Which statement describes FortiPresence location map functionality?
- A. Provides real-time insight into user online activity
- B. Provides real-time insight into user purchase activity
- C. Provides real-time insight into user usage stats
- D. Provides real-time insight into user movements
Answer: D
Explanation:
Explanation
(Page 88 Study Guide) "FortiPresence provides data and analytics based on demographic segmentation and visitor movement between areas" According to the web search results, FortiPresence location map functionality provides real-time insight into user movements. It uses the location data from the Fortinet access points to detect each visitor's smartphone Wi-Fi signal and track their location and behavior within the site. It also provides data visualization in a customizable format, such as heat maps and animated flows, to show the visitor traffic and movement patterns.
This geographical data analysis can help improve visitor experiences and business outcomes.
References: Location Analytics | FortiPresence 22.4.0 - Fortinet Documentation, FortiPresence Data Sheet
NEW QUESTION # 28
Which statement is correct about security profiles on FortiAP devices?
- A. Security profiles can only be applied to unencrypted wireless traffic.
- B. Security profiles are only supported on Bridge-mode SSIDs.
- C. Security profiles can only be applied via firewall policies on the FortiGate.
- D. Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic.
Answer: D
Explanation:
Explanation
Security profiles are a feature that allows FortiAP devices to apply various security functions to the wireless traffic, such as antivirus, web filter, application control, intrusion prevention, and botnet scanning. Security profiles can be enabled on both tunnel-mode and bridge-mode SSIDs, and can be applied either through the wireless controller configuration or through firewall policies on the FortiGate device. Security profiles can also inspect encrypted wireless traffic, as long as the FortiAP device has access to the encryption keys.
Security profiles on FortiAP devices can use FortiGate subscription services to inspect the traffic, such as FortiGuard Antivirus, FortiGuard Web Filter, FortiGuard Application Control, and FortiGuard IPS. This means that the FortiAP device can leverage the latest threat intelligence and updates from Fortinet to protect the wireless network from malicious or unwanted content.
Therefore, the correct answer is D. Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic.
References:
FortiAP-S and FortiAP-U bridge mode security profiles
Configuring security | FortiAP / FortiWiFi 6.4.2
Security profiles - Fortinet Document Library
NEW QUESTION # 29
As standard best practice, which configuration should be performed before configuring FortiAPs using a FortiGate wireless controller?
- A. Set the wireless controller country setting
- B. Preauthorize APs
- C. Create a custom AP profile
- D. Create wireless LAN specific policies
Answer: C
NEW QUESTION # 30
How can you find upstream and downstream link rates of a wireless client using FortiGate?
- A. On the FortiGate GUI, using the WiFi Client monitor
- B. On the FortiGate CLI, using the diag wireless-controller wlac -d Sta command
- C. On the FortiAP CLI, using the cw_diag -d sta command
- D. On the FortiAP CLI, using the cw_diag ksta command
Answer: A
Explanation:
Explanation
The WiFi Client monitor on the FortiGate GUI shows the upstream and downstream link rates of a wireless client, along with other information such as MAC address, SSID, IP address, signal strength, and connection time. The link rates indicate the maximum data rates that the client can achieve in both directions.
References: Secure Wireless LAN Course Description, page 7; [FortiOS 6.4.0 Handbook - Wireless Controller], page 37.
NEW QUESTION # 31
......
100% Free NSE6_FWF-6.4 Files For passing the exam Quickly: https://www.prep4sureexam.com/NSE6_FWF-6.4-dumps-torrent.html
NSE6_FWF-6.4 Dumps Questions Study Exam Guide : https://drive.google.com/open?id=1Bi9--ycmtsTlPnopzNrAPDBOtzh8E8vT