[Aug-2024] NACE-CIP2-001 Dumps PDF - NACE-CIP2-001 Real Exam Questions Answers
NACE-CIP2-001 Dumps 100% Pass Guarantee With Latest Demo
NEW QUESTION # 20
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Cost
- B. Iron content
- C. Appearance
- D. Safety
Answer: B
NEW QUESTION # 21
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Fusion Bonded Epoxy
- B. 3-Layer Polyethylene (PE)
- C. Coal Tar Enamel
- D. 2-Layer Polyethylene (PE)
Answer: B
NEW QUESTION # 22
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Cohesion failure
- B. Glue failure
- C. Adhesion failure
- D. Cold flow or creep
Answer: D
NEW QUESTION # 23
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that only technical experts would understand
- B. Language that another NACE Inspector would understand
- C. Language that only in the project would understand
- D. Language that the most would understand
Answer: D
NEW QUESTION # 24
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Review the NCR with the other Inspector
- B. Request a re-blast of the item in question
- C. Verbally challenge the NCR
- D. Consult your supervisor
Answer: D
NEW QUESTION # 25
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Liquid epoxies
- B. Heat-shrink sleeves
- C. Concrete
- D. Coal Tar Enamel
Answer: A
NEW QUESTION # 26
Thermal Spray coatings provide:
- A. Inhibitive protection
- B. Barrier protection
- C. Thermal protection
- D. Sacrificial protection
Answer: D
NEW QUESTION # 27
Ideally, documentation requirements should be defined:
- A. In the specification
- B. At the pre-job conference
- C. By the inspector
- D. By the contractor
Answer: A
NEW QUESTION # 28
The best choice of instrument for holiday testing of thick film concrete coatings is:
- A. High Voltage DC Constant Current
- B. High Voltage DC Pulse Type
- C. High Voltage AC
- D. Low Voltage Sponge Type
Answer: A
NEW QUESTION # 29
When ASIN D 3363 is specified the Inspector must:
- A. Record the highest value attained
- B. Record the two end points identified in the standard
- C. Record the percentage of failure
- D. Use the correct solvent
Answer: B
NEW QUESTION # 30
Coating application to concrete substrates is:
- A. Not required as Concrete is inorganic
- B. The same as coating steel
- C. Less challenging, than coating steel
- D. More challenging than coating steel
Answer: D
NEW QUESTION # 31
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. False
- B. True
Answer: A
NEW QUESTION # 32
Which is used to calibrate a pH meter?
- A. Deionized water
- B. Standard solvent solution
- C. Distilled water
- D. Standard buffer solution
Answer: D
NEW QUESTION # 33
Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?
- A. 3-Layet Polyethylene (PE)
- B. Coal Tar Enamel
- C. 2-Layet Polyethylene (PE)
- D. Concrete
Answer: D
NEW QUESTION # 34
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?
- A. Acid etching
- B. Sacking
- C. High-pressure water washing
- D. Stoning
Answer: A
NEW QUESTION # 35
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. True
- B. False
Answer: A
NEW QUESTION # 36
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Review the standard with the Contractor and re-inspect the floor
- B. Request that the Contractor re-blast the floor
- C. Shut the job down
- D. Call your supervisor
Answer: A
NEW QUESTION # 37
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Express a willingness to work with the site team and follow the specification
- B. Challenge the supervisor's authority
- C. Defend the previous inspector
- D. Suggest to the Owner that the supervisor should be removed from site
Answer: A
NEW QUESTION # 38
All of these are advantages of using repair patches EXCEPT
- A. barrier to moisture and corrosion.
- B. special tools or equipment are required.
- C. excellent abrasion resistance.
- D. inert to common acids, alkalis, and solvents.
Answer: B
NEW QUESTION # 39
You can use magnifiers to examine all of the following EXCEPT
- A. Surface cleanliness
- B. Mill scale
- C. Blisters
- D. Surface profile
Answer: A
NEW QUESTION # 40
NACE No.13/ SSPC 6 identifies the use of:
- A. Watterjetting only
- B. Steam cleaning only
- C. Abrasive blasting only
- D. Various methods of cleaning
Answer: D
NEW QUESTION # 41
External coatings applied to buried pipelines are generally tested for:
- A. Chalking resistance
- B. Cathodic disbondment
- C. Solvent resistance
- D. Gloss level
Answer: B
NEW QUESTION # 42
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. coatings are more durable than linings.
- B. linings are more durable than coatings.
- C. coatings are expected to degrade over time.
- D. linings protect the contents and the container.
Answer: D
NEW QUESTION # 43
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:
- A. Conductive coatings applied to a magnetic metallic substrate
- B. Magnetic coatings applied to a magnetic metallic substrate
- C. Conductive coatings applied to a cementitious substrate
- D. Non-Conductive coatings applied to a conductive metallic substrate
Answer: D
NEW QUESTION # 44
A single component water borne acrylic coating cures by:
- A. Solvent Evaporation
- B. Oxidation
- C. Co-Reaction
- D. Coalescence
Answer: D
NEW QUESTION # 45
......
Dumps Real NACE NACE-CIP2-001 Exam Questions [Updated 2024]: https://www.prep4sureexam.com/NACE-CIP2-001-dumps-torrent.html
Prepare NACE-CIP2-001 Question Answers Free Update With 100% Exam Passing Guarantee [2024]: https://drive.google.com/open?id=1DbY_EPGBQO9FDSkipDzkYfhHIEgjrn6C