Latest [Dec 27, 2021] NACE-CIP2-001 Exam Questions – Valid NACE-CIP2-001 Dumps Pdf
NACE-CIP2-001 Practice Test Questions Answers Updated 100 Questions
NEW QUESTION 45
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Use a generally accepted industry standard and to take readings
- B. Call your supervisor
- C. Develop your own methodology and proceed take the readings
- D. Refuse to take readings until an is in place
Answer: A
NEW QUESTION 46
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Ignore the situation
- B. Require the Applicator to remove the coating
- C. Stop the job
- D. Advise the Owner and write a Non-Conformance report
Answer: B
NEW QUESTION 47
Surface preparation methods for Non-ferrous metals are:
- A. The same for all Non-FetT0us metals
- B. Specific for each type of Non-ferrous metal
- C. Not required
- D. The same as for Ferrous metals
Answer: B
NEW QUESTION 48
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?
- A. Acid etching
- B. Stoning
- C. Sacking
- D. High-pressure water washing
Answer: A
NEW QUESTION 49
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 50 double rubs with a saturated cloth.
- B. 25 double rubs with a saturated cloth.
- C. 25 single rubs with a saturated cloth.
- D. 35 single rubs with a saturated cloth.
Answer: A
NEW QUESTION 50
NACE No.13/ SSPC 6 identifies the use of:
- A. Abrasive blasting only
- B. Various methods of cleaning
- C. Watterjetting only
- D. Steam cleaning only
Answer: B
NEW QUESTION 51
When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:
- A. Implement immediate to get them motivated
- B. Give them as much advance notice as possible about upcoming changes
- C. Make sure they are the center of attention in all site meetings
- D. Challenge their value to the team and try to get them out of their comfort zone
Answer: B
NEW QUESTION 52
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. coating type.
- B. type of dehumidification equipment (refrigerant or desiccant).
- C. manufacturer of the equipment.
- D. time of the year (winter/summer).
Answer: A
NEW QUESTION 53
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A hardness tester
- B. A set of 14 pencils of varying hardness
- C. A destructive paint inspection Tooke gauge
- D. A mechanical adhesion tester
Answer: C
NEW QUESTION 54
You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Accept assignment without hesitation
- B. Review the NACE Attestation prior to making a decision
- C. Meet with the prospective employer to scope of your role
- D. Advise the prospective employer that you cannot accept the position
Answer: B
NEW QUESTION 55
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Appearance
- B. Safety
- C. Iron content
- D. Cost
Answer: C
NEW QUESTION 56
Linings are used on the interior of pipelines to
- A. protect the transported product.
- B. reduce magnetic polarity.
- C. provide protection against soil chemicals.
- D. afford limited temperature insulation.
Answer: A
NEW QUESTION 57
All of these are advantages of using repair patches EXCEPT
- A. barrier to moisture and corrosion.
- B. inert to common acids, alkalis, and solvents.
- C. special tools or equipment are required.
- D. excellent abrasion resistance.
Answer: C
NEW QUESTION 58
Inspection and Test plans are developed by referencing:
- A. The Specification, SDS, relevant Standards and Codes
- B. The Specification, TDS, relevant Standards and Codes
- C. The Specification, Application Guidelines, 'Relevant Standards and Codes
- D. The Specification, Safety Manual, Relevant Standards and Codes
Answer: B
NEW QUESTION 59
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. urethanes.
- B. epoxies.
- C. inorganic zincs.
- D. powder coatings.
Answer: C
NEW QUESTION 60
Generally for safety considerations, waterjetting hose connections use
- A. filters.
- B. a whip-lock device.
- C. an oil/water separator.
- D. a long wand.
Answer: B
NEW QUESTION 61
Coating application to concrete substrates is:
- A. Less challenging, than coating steel
- B. More challenging than coating steel
- C. Not required as Concrete is inorganic
- D. The same as coating steel
Answer: B
NEW QUESTION 62
Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?
- A. Mandatory
- B. De facto
- C. Consensus
- D. Voluntary
Answer: D
NEW QUESTION 63
You can use magnifiers to examine all of the following EXCEPT
- A. Surface cleanliness
- B. Surface profile
- C. Mill scale
- D. Blisters
Answer: A
NEW QUESTION 64
Coating Surveys are legally required:
- A. On food and beverage vessels and can linings
- B. On water tanks and potable water pipelines
- C. On high pressure gas lines and fireproofed structures
- D. On commercial marine vessels and offshore platforms
Answer: D
NEW QUESTION 65
Non-Conformance Reports are designed to:
- A. Punish the Contractor for substandard work
- B. To identify items that do not meet the specification requirements
- C. Assist the Owner in negotiating credits from the Contractor
- D. Elevate the status of the Inspector
Answer: B
NEW QUESTION 66
......
NACE-CIP2-001 dumps Sure Practice with 100 Questions: https://www.prep4sureexam.com/NACE-CIP2-001-dumps-torrent.html
Get New NACE-CIP2-001 Certification – Valid Exam Dumps Questions: https://drive.google.com/open?id=1sUbaOk5a9WVOmveJjYWpekns4L51XMFR